Reference Manual. INTRODUCTION Thank you for purchasing the Alesis ADAT- XT Digital Multitrack Tape Recorder. To take full advantage of the XT’s functions, . User manual for the device Alesis ADAT-XT. Online user manual database. musical instrument, dj equipment manuals, user guides, spec sheets. Alesis ADAT-XT Recording Equipment User Manual. Page 1. Page 2. Page 3. Page 4.

Author: Kazrasho Galkis
Country: Liberia
Language: English (Spanish)
Genre: Medical
Published (Last): 26 September 2012
Pages: 434
PDF File Size: 15.81 Mb
ePub File Size: 4.46 Mb
ISBN: 674-6-53724-750-2
Downloads: 76633
Price: Free* [*Free Regsitration Required]
Uploader: Kazilkis

The shipping carton was designed toprotect the unit during shipping. Page 35 Basic Operations: Autolocation Controls Chapter 4: Page 74 Chapter 6: ApplicationsIf your sequencer generates MMC commands, you should be able to put yoursequencer into play and have the XT follow along. Page 46 Daat 4: To extend the format on a partially formatted tape: Page 58 Chapter 4: Comments to this Manuals Your Name.

These are compatible with lowimpedance, unbalanced, dBV outputs typical of equipment such as mixers,synthesizers, samplers, direct boxes, etc. When you install it, keep in mind that heat is the major enemy ofelectronic equipment. Page 50 Chapter 4: The result is a perfect digitalduplication of the original.

To achieve the fastest chase-lockperformance from a multi-ADAT system, use the Locate points whenever possible. Page 17 Chapter 2: If the tape is moving, it will stop before ejecting. For more information on using the Track Copy function, see page JThe XT can produce a transient audio signal during power up and power down. Write Protect Override the last valid adag it reads from tape.


The EXT icon lights. Table of Contents Kanual to my manuals Add.


The larger of the two outer key notches is at the bottom. Alesis Sync Cables are available in three different lengths: In this situation, the XT assumes the tape length to be that of a ST tape.

Page 36 Chapter 4: In a mixer, a bus is usually awire that is or can be made common to the outputs of any or all channels in adaat. If only one tape is found to cause this problem, don’t use it. Basic Audio Hookup Chapter 1: Page 87 Appendix D: Page 44 Chapter 4: No user adjustment is necessary. It shows the current level of each of the eight audio tracks, it shows the current tape position zdat in hours, minutes, seconds, and ths of seconds, and shows the current modes of the many parameters available.

Page 38 Chapter 4: Replace only with the same or equivalent type. Get familiar with them by using kanual while watching the TIME counter.

The option to print the manual has also been provided, and you can use it by clicking the link above – Print the manual.

Customers outside theUSA and Canada are not convered by this Limited Warranty and may or may not becovered by independent distributor warranty in the county of sale.


The larger of the two outer key notches is at the bottom. Eight18 bit linear audio, times oversampling, singl Page 89 Appendix D: Page 25 Chapter 2: The processinvolves formatting a tape see previous tutorialputting one or more tracks intorecord-ready, adjusting record levels on arat mixer, setting the input monitor mode,locating to the start tape address and engaging record.


Page 76 Chapter 6: Glossaryby the motion picture and television industries. In thissituation, the XT assumes the tape length to be that of a ST tape. Naturally, the audio signals would need to be split and connected to both sets of manuxl. For your convenience If looking through the Alesis ADAT-XT user manual directly on this website is not convenient for you, there are two possible solutions: The currently selectedmode may be determined by observing the peak meters themselves.

The XT provides eight dBV analog outputs via phono connectors. We cannot overemphasize the importance of this.

Alesis ADAT-XT Reference Manual

Next, select the source tracks, select record enable the destination tracks, and initiate recording. TroubleshootingFormula or Fantastik. Do notoperate the unit.

Page 28 Chapter 3: Troubleshootingshould asat be aware that it is extremely easy to damage your heads and othersensitive parts of your ADAT. Got it, continue to print.